Nake, waxed before loading.
N/M, spraying wax for container side loader when shipping by bulk
or ro-ro vessel. Container side loader can be shipped either by
container ship or three/four units.
Any port in China
Lead Time :
|Quantity(Units)||1 - 10||>10|
|Est. Time(days)||25||To be negotiated|
Startrailer Red 3 Axle 40 Ft Skeletal Container Trailer For Truck
The 40ft gooseneck chassis is designed for use in stevedoring and
transporting of 1x20ft cargo containers.
Length: Approx 16,429 mm
Width: Approx 2,470 mm
Height: Approx 1,388 mm
King Pin Location: Approx 1000 mm from the front face of the front bolster
Axle spacer: Approx 9,930mm + 1,310mm + 1,310mm
Landing Gear location: Approx 2,620mm behind the king pin location
(The above dimension will be adjusted according to the tractor specification)
Tare Weight (Tolerance: 0~4%): Approx 6,000 kg
Max. Payload: 30,480kg
GVWR: Approx 36.480kg
a) high tensile steel to fabricated “H” beam, top/bottom flange 16mm
thickness, web 8mm thickness. It is Sufficient for 30,000kg Payload
Trailer. Steel: Q345.
b) No bending is allowed on the main beam chassis. The vertical
deflection of the main beam at center at unloaded is under +12 mm
Front and rear bolster are of hot roller “C” type channel steel
sufficient for 30,000kg Payload Trailer. Steel: Q345.
There are hot roller “C” type square channel steel cross member and
combination. Height tensile steel plate to support the twist locks
And height tensile steel plate with triangle gusset to strength the
frame at the location of suspension when the container loaded in.
Material: High strength low alloy steel Q345 with 350 Map yield strength is
used for welded I-beam and Q235 in other fabricated parts.
Properties of steel material
|Yield Point (min.)||Tensile Strength (min)|
|Kg/sq. mm||Psi.||Kg/sq. mm||Psi.|
*CIS: China Industrial Standards
OEM Parts Configuration:
King Pin: SAE standard 2” (exchangeable) bolting king pin, Supplier: JOST
Made in China.
Twist Locks: Four (4) twist retractable locks.
Landing Gear: 2 speed road side winding with sand shoe. Static Load: 50 ton.
Lift Load: 24 ton. Type: JOST D200T Made in China.
Suspension: Mechanical suspension with 7 pieces leaf springs. Famous Brand:
FUWA, Baoming etc Made in China.
Axles: Axle with 13 tons capacity. Famous Brand: CIMC, York, BPW, SAF etc
Made in China. Option is made by the factory.
Rims: 8.0-20, 10 Holes ISO, 12 pieces.
Tires: 11.00-20, 12 pieces; China Famous Brand: Linglong, Triangle,
Jinguan etc. Option is made by the factory.
Brake System: Dual or single pneumatic brake system; WABCO relay emergency
valve, none ABS brake system.
Brake Chamber: 30/30 type on the rear axle, 30 types on the front axle
Electrical System: 24 volt electrical system with 7-pin connector and modular wiring
|Tail/Stop light: Two, Red.||Rear turn signal light: Two, amber|
|License light: One, white||Front clearance/marker light,|
|Reversing light, Side Lights and Rear fog light.|
Spare Tire Carrier: Equipped two, without tire.
Side Guard: Side Protection.
Reflector: 2-Nos triangle shaped Red Reflectors at Rear.10 pieces Reflectors
strip (Conspicuity tape) each side.
Tool Box: Equipped one
Mudguards: PVC, 2 pieces.
Color: The Color is made by customer’s requirement.
Painting: Entire chassis is sand blasted after welding to commercial grade
and painted with high build primer and 2 coats of high build
automotive final paint.
Over lapping area are to be prime coated before assembly.
Epoxy zinc rich primer 20 microns
Epoxy high solid primer 80 microns
Chlorinated rubbers primer 70 microns
Chlorinated rubbers finish 50 microns
Minimum total DFT 220 microns
Each coating has been cured in heat booth before applying the next
The frame of container chassis series will be constructed with
steel frame. All steel work will be built up by means of automatic
and semi-automatic CO2 gas arc welding and shielded arc flux-coated
welding. All welding equipment shall be maintained in good working
order to produce acceptable weld quality.
For all fabrication work, the welding procedure and inspection on
the quality of welds shall follow: BS5133 or ANSI/AWS D1.1-98
Prior to welding
All the steel plate surface prior to forming or after will be
degreased and shot blasted to Swedish Standard SA 2.5 to obtain the
surface roughness at 25 to 35 microns which can result in the
remove of all the rust, dirt, mill scale and all other foreign
materials. All the steel surface will be coated with zinc primer
paint immediately to the thickness of 10 microns after
After welding of chassis frame, all welded area in shot blasted to
SA 2.5 to remove all the welding fluxes, spatters, burnt primer
coatings caused by welding heat and other foreign materials and
followed with the secondary zinc primer paint 40 microns operation
1) All the details not mentioned above should comply with Chinese
2) These specifications are given as information. CIMC reserves its
right to change them without previous notice.
1.Reply your inquiry in 12 working hours .
2.Expeirenced staffs answer all your questions.
3.Customer's design is available for certain products (OEM)
4.Spare parts for all types of engine machinery with reasonable
5.Different kinds of semi trailer can be provided with competitive
Click this link to talk to us: