Thread Connection P5 Air Compressor Solenoid Valve 220VAC / 230VAC / 240VAC

Thread Connection P5 Air Compressor Solenoid Valve 220VAC / 230VAC / 240VAC

Applicability

1 . Fluid temperature must be less than the marked temperature .

2 . If fluid is not high cleanliness , should be installed a filters in front of the solenoid valve , general solenoid valve is better claim to medium cleanness

3 . Pay attention to the orifice and port size ; usually only open and close two type ; Conditions permit , please install bypass pipe , easy maintenance ; When there is water drain to customize solenoid valve opening and closing time regulation .

4 . Pay attention to the environmental temperature on the influence of solenoid valve .

5 . Power supply current and power consumption should be selected according to the output capacity , power supply voltage generally allow + / - 10 % , must pay attention to AC starting the VA value is higher .

Reliability

Ction time is very short at high frequency generally choose directly acting , large diameter choose fast series .

Security

1 . Nominal pressure solenoid valve of the highest calibration must be more than the highest pressure in the pipeline , otherwise life will shorten or other unexpected circumstances .

2 . Corrosive liquid should be chosen in all stainless steel type , appropriate chooses the corrosive fluid plastic king ( LF ) solenoid valve .

Economy

There are a lot of solenoid valve can be common use , but on the basis of can satisfy the above three terms , should choose the most economical products

Brass

1: 2 Way normally closed solenoid valve , Closed when de - energized , open when energized .
2: Serialized products , small in size , large flow rate , widely use
3: Body material : forged brass . Orifice : Φ 10 . 5mm
4: Ambient Temp. 0 ℃ ~ 65 ℃ , Fluids Temp : 0 ℃ ~ 130 ℃ .
5: Flow as the arrow , mounts in any position ; Best position is solenoid vertical and upright direction .
6: Voltage: 220VAC / 230VAC / 240VAC / 110VAC / 24VAC 50 / 60HZ 24VDC / 12VDC ;
Voltage Tolerance : + 10 % to - 10 % applicable voltage
7: This series valves are offered NBR , VITON , EPDM , etc . For Seals and diaphragm to provide on - off control of various fluids .

Stainless Steel

1: 2 Way Normally closed solenoid valve , closed when de - energized , open when energized .
2: Serialized produvts , small in size , large flow rate , widely use
3: Body material : SS316 Orifice Φ 8mm
4: Ambient Temp 0 ℃ ~ 65 ℃ Fluids Temp . : 0 ℃ ~ 130 ℃
5: Flows as the arrow , mounts in any position ; best position is solenoid valve vertical and upright direction .
6: Voltage : AC24V / 110V / 220V / 230V / 240V 50 / 60HZ DC24V / 12V /
Voltage Tolerance : + 10 % ~ - 10 % applicable voltage
7: This series valves are offered NBR , VITON , EPDM Etc , Forseals and diaphragm to provide on / off control of various fluids .

Why choose us

1: Various style for each products and completely series pneumatic products .
2: Large stock for fast shipping .
3: Sample order & small quantity order is acceptable .
4: Customize according to your special request .
5: Reliable quality assured and active after-sell service
6: One year quality guarantee

FAQ

Q: How much is our minimum order quantity ?
A: Our minimun quantity is 1 Piece .

Q: Could you offer the free samples ?
A: Yeah, we could offer the free samples based on special customer.pre-production sample,production sample.

Q: What ' s your business scope ?
A: Our business scope is SMC type high quality cylinder , air source treatment , solenoid valve ,water valve,steam valve, mechnical valve ,foot valve,angle seat valve,anti-explosion valve,pluse vlave, pneumatic valve ,hydraulic ball valve,hydraulic ss ball valve,hydraulic check valve,hydraulic solenoid valve ,all type of coil,lubrication pump and parts,SS316 fitting,quick coupler , etc .

Q: what types of products you can make ?
A: We can make many kinds of stainless steel materials and brass,aluminum . Valve / solenoid valve / electric valve / pneumatic valve and air cylinder products and so on .

Q: Do your company have specialized technical personnel ?
A: Design as your requirements,and have QC for make 100% inspection

Q: Can the product be made with our logo and brand ?
A: Yes , of course , we can make . we are OEM supplier for years and professional to make . But you need give us the authorization for work.

NINGBO SANMIN IMPORT & EXPORT CO.,LTD. was established in 2014.Our company is mainly engaged in instrumentation, pneumatic and hydraulic industry accessories and services, has more than 10 series of core products.Focusing on the production of automatic machinery to provide a variety of options, products have a wide range of applications.

Sanmin is an industrial and trade enterprise, has a strict quality control system from material selection, inspection workshop, product testing, production, inspection, packaging design to shipment.At present, the company's trade scale is expanding day by day, the customers spreads over more than 20 countries.

We are strictly abides by Chinese laws and regulations, and has won the trust of customers at home and abroad with good reputation. Welcome to telephone and send E-mail to communication, sincerely cooperate, and seek common development.

Supply Original FESTO,SMC,CKD,NORGEN,MARSH,BELLOFRAM,BELGAS,MUELLER,SBFEC.

NINGBO SANMIN IMPORT AND EXPORT CO.,LTD.

INA CHEN

Whatsapp/wechat: +86 15168536055

Desk phone :+86 0574 88915660

Skype: fhtrust

INA@PNEUHYDR.COM